| № | Номер | Название | Опции | Альт |
|---|
| 32978 | PLATE ASSY. | CLAMP -, Serial Range: tube-hose | |
| NSS | NOT SOLD SEPARAT | 5/16" - 18 NC x 1-3/4" hex. head cap screw (13-528) | |
| NSS | NOT SOLD SEPARAT | 5/16" lockwasher (92-5) | |
| NSS | NOT SOLD SEPARAT | 5/16" hex. nut (25-105) | |
| D23974 | ELBOW | - 90 degrees adjustable street, upper stabilizer port (Used with D24409 hose - see D29313) | |
| NSS | NOT SOLD SEPARAT | "O" ring seal, D23974 elbow (218-5007) | |
| D24409 | | HOSE - valve to upper and lower ports stabilizer cylinder (3/8" I.D. x 3/4" O.D. x 20" long) See D29311 hose, D29313 elbow, and D29145 elbow | |
| | D29145, D29311, and D29313 should be used in place of D24409. | | |
| NSS | NOT SOLD SEPARAT | "O" ring seal, D24409 hose (218-5008) | |
| D25052 | CYLINDER - stabilizer, hydraulic (With tie rods) See Figure 094 for breakdown (When stock is exhausted use D27754 cylinder and D27859 tube) | | |
| D26361 | FITTING | ELBOW - 90 degrees, hose to tube on stabilizer cylinder | |
| D26375 | | TUBE - lower port D25052 stabilizer cylinder (See D27859) | |
| D27754 | CYLINDER | - stabilizer, hydraulic (Without tie rods) See D25052 (When replacing D25052 cylinder also order 1-D27859 tube) See Figure 095 for breakdown | |
| D27859 | TUBE | - lower port D27754 stabilizer cylinder (See D26375) | |
| NSS | NOT SOLD SEPARAT | "O" ring seal, D27859 tube (218-5007) | |
| D29145 | ELBOW UNION | ELBOW - 90 degrees adjustable, upper and lower valve ports (Used with D29311 hose) Backhoe serial no. 4066819 and after) | |
| | D29145, D29311, and D29313 should be used in place of D24409. | | |
| NSS | NOT SOLD SEPARAT | "O" ring seal, D29145 elbow (218-5008) | |
| D29311 | | HOSE - upper and lower valve ports to stabilizer (3/8" I.D. x 3/4" O.D. x 20" long) When replacing D24409 hoses also order 1-D29145 elbow and 1-D29313 elbow) (Backhoe serial no. 4066819 and after) | |
| | D29145, D29311, and D29313 should be used in place of D24409. | | |
| D29313 | ELBOW | - 90 degrees adjustable, upper port of stabilizer cylinder when D29311 hose is used (Backhoe serial no. 4066819 and after) | |
| | D29145, D29311, and D29313 should be used in place of D24409. | | |
| 32978 | PLATE ASSY. | CLAMP - tube to hose, swing cylinder hydraulics (before s/n 4042173 and after) | |
| NSS | NOT SOLD SEPARAT | 5/16" - 18 NC x 1-3/4" hex. head cap screw (13-528), swing cylinder hydraulics (before s/n 4042173 and after) | |
| NSS | NOT SOLD SEPARAT | 5/16" lockwasher (92-5), swing cylinder hydraulics (before s/n 4042173 and after) | |
| NSS | NOT SOLD SEPARAT | 5/16" - 18 NC hex. nut (25-105), swing cylinder hydraulics (before s/n 4042173 and after) | |
| 50875 | NUT | - hex. jam, special (Bulkhead tees and criss-cross relief valve (7/8" - 14 NF), swing cylinder hydraulics (before s/n 4042173 and after) | |
| D24413 | HOSE ASSY. | HOSE - bulkhead tube to swing cylinder ports (3/8" I.D. x 3/4" O.D. x 20-1/2" long), hydraulics (before s/n 4042173 and after) | |
| NSS | NOT SOLD SEPARAT | 3/8" NPT 90 degrees street elbow (221-413) Use D26372, swing cylinder hydraulics (before s/n 4042173 and after) | |
| D25025 | | CYLINDER - swing, hydraulic (See Figure 090 for breakdown) Use D27750, (before s/n 4042173 and after) | |
| D25084 | | TUBE - bulkhead tee to hose, swing cylinder hydraulics (before s/n 4042173 and after) | |
| D25091 | | HOSE - elbow to lower port criss-cross relief valve (1/2" I.D. x 7/8" O.D. x 18-3/4" long) Use D29156, swing cylinder hydraulics (before s/n 4042173 and after) | |
| D25092 | | HOSE - lower control valve port to upper port criss-cross relief (1/2" I.D. x 7/8" O.D. x 17-1/4" long) Use D29153, swing cylinder hydraulics (before s/n 4042173 and after) | |
| D25272 | | TEE - bulkhead (Original equipment on backhoes before serial no. 4042180 and after serial no. 4058655) Includes 2-50875 nuts (See D26883), swing cylinder hydraulics (before s/n 4042173 and after) | |
| NSS | NOT SOLD SEPARAT | 7/8" - 14 NF hex. jam nut, use 50875 (25-1514), swing cylinder hydraulics (before s/n 4042173 and after) | |
| D25816 | X | HOSE - lower control valve port to upper port criss-cross relief (1/2" I.D. x 7/8" O.D. x 17-1/2" long) Use D29153, swing cylinder hydraulics (before s/n 4042173 and after) | |
| NSS | NOT SOLD SEPARAT | "O" ring seal, D25816 hose (218-5008), swing cylinder hydraulics (before s/n 4042173 and after) | |
| D25819 | | ELBOW - 90 degrees adjustable street (Upper valve port) Use D29781, swing cylinder hydraulics (before s/n 4042173 and after) | |
| NSS | NOT SOLD SEPARAT | "O" ring seal, D25819 elbow (218-5008), swing cylinder hydraulics (before s/n 4042173 and after) | |
| D25828 | | NUT - hex. jam, special (Bulkhead tees and criss-cross relief valve) 7/8" - 14 NF, swing cylinder hydraulics (before s/n 4042173 and after) | |
| D26372 | ELBOW UNION | ELBOW - 90 degrees street 3/8" NPT (Hose to swing cylinders), hydraulics (before s/n 4042173 and after) | |
| D26373 | | TUBE - rear port swing cylinder to hose (See D28707), hydraulics (before s/n 4042173 and after) | |
| NSS | NOT SOLD SEPARAT | 3/8" NPT x 1/2" JIC male elbow (218-484), swing cylinder hydraulics (before s/n 4042173 and after | |
| D26883 | VALVE - criss-cross relief (Original equipment on backhoes serial number 4042180 to 4058655) See D25272 (See Figure 110for breakdown), swing cylinder hydraulics (before s/n 404217. and after) | | |
| D27750 | CYLINDER ASSY. | CYLINDER - swing, hydraulic (See Figure 092 for breakdown) See D25025, (before s/n 4042173 and after) | |
| D28156 | | VALVE - flow control, swing cylinder hydraulics (before s/n 4042173 and after) | |
| NSS | NOT SOLD SEPARAT | 3/8" NPT to 1/2" NPT 90 degrees female reducing elbow (221-382), swing cylinder hydraulics (before s/n 4042173 and after) | |
| NSS | NOT SOLD SEPARAT | 3/8" NPT to 1/2" NPT 90 degrees street reducing elbow (221-561), swing cylinder hydraulics (before s/n 4042173 and after) | |
| NSS | NOT SOLD SEPARAT | 1/2" NPT x 1-1/8" long pipe nipple (221-185), swing cylinder hydraulics (before s/n 4042173 and after) | |
| NSS | NOT SOLD SEPARAT | 1/2" NPT x 2-1/2" long pipe nipple (221-191) Used in place of D28156 flow control valve and 221-185 nipple on units with a regenerative circuit, swing cylinder hydraulics (before s/n 4042173 and after) | |
| D28707 | | TUBE - rear port of swing cylinder to hose (Used with D27750 cylinder) See D26373, hydraulics (before s/n 4042173 and after) | |
| D29153 | HOSE ASSY. | HOSE - lower valve port to upper port criss-cross relief valve (1/2" I.D. x 31/32" O.D. x 17-1/2" long), swing cylinder hydraulics (before s/n 4042173 and after) | |
| NSS | NOT SOLD SEPARAT | "O" ring seal, D29153 hose (218-5008), swing cylinder hydraulics (before s/n 4042173 and after) | |
| D29156 | | HOSE - upper valve port to lower port criss-cross relief valve (1/2" I.D. x 31/32" O.D. x 18-3/4" long), swing cylinder hydraulics (before s/n 4042173 and after) | |
| D29781 | | ELBOW - 45 degrees adjustable (Upper valve port), swing cylinder hydraulics (before s/n 4042173 and after) | |
| NSS | NOT SOLD SEPARAT | "O" ring seal, D29781 elbow (218-5008), swing cylinder hydraulics (before s/n 4042173 and after) | |
| D11354 | KIT - flow control for swing cylinder (Includes following items), valve ( for field installation) | | |
| D28156 | | VALVE - flow control, valve kit, (for field installations) | |
| NSS | NOT SOLD SEPARAT | 3/8" NPT to 1/2" NPT 90 degrees female reducing elbow (221-382), D11354 flow control valve kit (for field installation) | |
| NSS | NOT SOLD SEPARAT | 3/8" NPT to 1/2" NPT 90 degrees street reducing elbow (221-561), D11354 flow control valve kit (for field installation) | |
| NSS | NOT SOLD SEPARAT | 1/2" NPT x 1-1/8" pipe nipple (221-185), D11354 flow control valve kit (for field installation) | |
