| № | Номер | Название | Опции | Альт |
|---|
| D23203 | BUSHING | - lower tower swing | |
| D23519 | AXLE PIN | PIN - pivot, lower tower swing | |
| NSS | NOT SOLD SEPARAT | 1/8" NPT 90 degrees grease fitting (219-55) | |
| D23523 | PIN | - pivot, boom, Serial Range: cylinder-tower | |
| NSS | NOT SOLD SEPARAT | 1-13/32" I.D. x 2-3/4" O.D. x #10 gauge standard wrot washer (192-2165) | |
| D23907 | SPACER | - bearing, upper swing (5/16" thick) | |
| D23909 | | BOLT - mounting, upper swing tower pivot to mounting frame | |
| NSS | NOT SOLD SEPARAT | 1/8" NPT straight grease fitting (219-1) | |
| NSS | NOT SOLD SEPARAT | 1-1/2" - 12 NF slotted hex. nut (129-234) | |
| NSS | NOT SOLD SEPARAT | 1/4" x 2" cotter pin (132-154) | |
| D25000 | BUSHING | - boom cylinder pivot | |
| D25025 | | CYLINDER - swing hydraulic (Early production - when stock is exhausted use D27750) See Figure 090 for breakdown | |
| D25040 | TOWER - swing (Includes 2-D23203 and 2-D25000 bushings) | | |
| D25075 | PIN | - pivot, swing cylinder piston rod to mounting frame | |
| D25278 | RING, SNAP | SNAP RING - D25075 pin (.062" thick) See D26918 | |
| D25280 | SNAP RING,#175, Ext | RING, Snap, , D23523 pin #175, Ext | |
| D25281 | RING, SNAP | SNAP RING - D23519 pin (.078" thick) See D26919 | |
| D25509 | WASHER | - D23519 pin (2-1/64" I.D. x 3" O.D. x #12 gauge) | |
| D25514 | | PIN - pivot, swing, Serial Range: cylinder-tower | |
| NSS | NOT SOLD SEPARAT | 1/8" NPT straight grease fitting (219-1) | |
| NSS | NOT SOLD SEPARAT | 5/8" - 11 NC x 2-3/4" hex. head cap screw (13-1044) | |
| NSS | NOT SOLD SEPARAT | 5/8" lockwasher (92-10) | |
| NSS | NOT SOLD SEPARAT | 5/8" - 11 NC hex. nut (25-1010) If used | |
| D25987 | X | PIN - pivot, Serial Range: boom-tower | |
| NSS | NOT SOLD SEPARAT | 1" - 8 NC x 2" hex. head cap screw (13-1632) Use 113-900 | |
| NSS | NOT SOLD SEPARAT | 1" - 8 NC x 2" Nylock self-locking bolt (113-900) | |
| NSS | NOT SOLD SEPARAT | 1" external tooth Shakeproof lockwasher, used with 13-1632 cap screw only (193-17) | |
| D25991 | | WASHER - D25987 pin (1-3/32" I.D. x 2-1/2" O.D. x 1/2" thick) (Not shown) | |
| D26305 | SPACER | - bearing, upper (3/8" thick) | |
| D26918 | SNAP RING,#125, Ext | RING, Snap, , D25075 pin (.093" thick) see D25278) #125, Ext | |
| D26919 | SNAP RING,#200, Ext | RING, Snap, , D23519 (.125" thick) see D25281 #200, Ext | |
| D26991 | BEARING | SPACER - bearing, upper (1/4" thick) | |
| D27750 | CYLINDER ASSY. | CYLINDER - swing, hydraulic (Late production - see D25025) See Figure 92 for breakdown | |
| D28266 | WASHER | - special (1-7/64" I.D. x 2-1/8" O.D. x #12 gauge) | |
| 36121 | BUSHING | - boom to tower and boom to dipper arm | |
| NSS | NOT SOLD SEPARAT | 1/8" NPT straight grease fitting (219-1), boom | |
| NSS | NOT SOLD SEPARAT | 1/8" NPT 67-1/2 degrees grease fitting (219-40), boom | |
| D23428 | BOOM - backhoe (Includes 4-36121 bushings, 1-straight grease fitting 219-1, 2-D25258 bushings, 1-67-1/2 degrees grease fitting 219-40, and 2-D25029 bushings) | | |
| D23517 | PIN | - pivot, dipper, Serial Range: arm-boom | |
| D23521 | AXLE PIN | PIN - pivot, crowd, Serial Range: cylinder-boom | |
| D23522 | AXLE PIN | PIN - pivot, boom, Serial Range: cylinder-boom | |
| NSS | NOT SOLD SEPARAT | 1-13/32" I.D. x 2-3/4" O.D. x #10 gauge standard wrot washer (195-2165), boom | |
| D25012 | | CYLINDER - crowd, hydraulic (Early production - with tie rods) When stock is exhausted, order 1-D27752 cylinder, 1-D29026 tube, and 1-218-5065 connector (See Figure 100 for breakdown), boom | |
| D25027 | | CYLINDER - boom, hydraulic (1-3/4" piston rod - with tie rods) When stock is exhausted order 1-D27751 cylinder, 1-D29020 tube, and 1-218-5065 connector (See Figure 096 for breakdown) | |
| D25029 | BUSHING | - crowd cylinder pivot, boom | |
| D25258 | BUSHING | - boom cylinder pivot | |
| D25280 | SNAP RING,#175, Ext | RING, Snap, , D23521 and D23522 pins, boom #175, Ext | |
| D25281 | RING, SNAP | SNAP RING - D23517 pin (.078" thick) See D26919, boom | |
| D25509 | WASHER | - D23517 pin (2-1/64" I.D. x 3" O.D. x #12 gauge), boom | |
| D26919 | SNAP RING,#200, Ext | RING, Snap, , D23517 pin (.125" thick) see D25281, boom #200, Ext | |
| D27156 | CYLINDER ASSY. | CYLINDER - boom, hydraulic (2" piston rod - with tie rods) When stock is exhuasted order 1-D27751 cylinder, 1-D29020 tube, and 1-218-5065 connector (See Figure 098 for breakdown) | |
| D27489 | | CYLINDER - crowd, hydraulic (Late production - with tie rods) When stock is exhausted order 1-D27752 cylinder, 1-D29026 tube, and 1-218-5065 connector (See Figure 102 for breakdown), boom | |
| D27751 | CYLINDER ASSY. | CYLINDER - boom, hydraulic (Late production - without tie rods) See D25027 and D27156 (See Figure 099 for breakdown) When replacing a cylinder with tie rods also order 1-218-5065 connector and 1-D29020 tube | |
| NSS | NOT SOLD SEPARAT | 3/4" JIC x 5/8" JIC straight connector (218-5065) Not shown, boom | |
| D27752 | CYLINDER ASSY. | CYLINDER - crowd hydraulic (Late production - without tie rods) See D25052 and D27489 (See Figure 103 for breakdown) When replacing a cylinder with tie rods also order 1-218-5065 connector and 1-D29026 tube, boom | |
| NSS | NOT SOLD SEPARAT | 3/4" JIC x 5/8" JIC straight connector (218-5065) Not shown, boom | |
| 30634 | BUSHING,32.05mm ID x 38.18mm OD x 17.6mm L | - link pivot at cipper arm, dipper | |
| 35288 | | PIN - pivot, bucket to dipper arm (Used on backhoe serial no. 4043057 and after) See D23354 | |
| NSS | NOT SOLD SEPARAT | 1/2" - 13 NC x 1" hex. head cap screw (13-816) Not shown, dipper arm | |
| NSS | NOT SOLD SEPARAT | 1/2" internal tooth Shakeproof lockwasher (192-32) Not shown, dipper arm | |
| 35290 | PIN | - pivot, dump link to bucket (Used on backhoe serial no. 4043057 and after) See D25021, dipper arm | |
| NSS | NOT SOLD SEPARAT | 1/2" - 13 NC x 1" hex. head cap screw (13-816), dipper arm | |
| NSS | NOT SOLD SEPARAT | 1/2" internal tooth Shakeproof lockwasher (193-32) Not shown, dipper arm | |
| D23203 | BUSHING | - dipper, Serial Range: arm-boom | |
| D23354 | | PIN - pivot, bucket to dipper arm (Used before backhoe serial no. 4043057) Use 35288 | |
| D23358 | | PIN - pivot, dipper arm to bucket linkage and bucket cylinder to bucket linkage | |
| D23360 | BUCKET - backhoe trenching (24") See Figure 28 for breakdown and other optional buckets (Machinery item), dipper arm | | |
| D23441 | AXLE PIN | PIN - pivot, crowd and bucket cylinder to dipper arm | |
| D23444 | BUSHING | - D23458 and D29512 dipper arm at bucket pivot and bucket linkage (See D32708) | |
| D23458 | | ARM - dipper (Includes 2-D23203 bushings, 4-D25029 bushings, and 4-D23444 bushings) Use D29512, arm | |
| NSS | NOT SOLD SEPARAT | 1/8" NPT straight grease fitting (219-1), dipper arm | |
| D23740 | BUSHING | - 35288 and 35290 pins (Not shown), dipper arm | |
| D24909 | | LINK - dump, bucket (Includes 4-DR10011 or D28021 bushings) When stock is exhausted use 1-D29992 link and 2-D30042 spacer washers, dipper arm | |
| D25021 | X | PIN - pivot, dump link to bucket (Used before backhoe serial no. 4043057) Use 35290, dipper arm | |
| D25022 | WASHER | - D25021 pin (17/32" I.D. x 1-3/4" O.D. x 3/16" thick), dipper arm | |
| D25029 | BUSHING | - crowd and bucket cylinder to dipper arm | |
| D25045 | CYLINDER - bucket, hydraulic (With tie rods) When stock is exhausted use 1-D27753 cylinder, 1-D29022 tube, and 1-218-5065 connector (See Figure 104 for breakdown), dipper arm | | |
| D25278 | RING, SNAP | SNAP RING - D23354 pin and D23358 pin (.062" thick) See D26918, dipper arm | |
| D25280 | SNAP RING,#175, Ext | RING, Snap, , D23441 pin, dipper arm #175, Ext | |
| D26918 | SNAP RING,#125, Ext | RING, Snap, , D23354 pin and D23358 pin (.093" thick) see D25278, dipper arm #125, Ext | |
| D27679 | | LINK - bucket, dipper arm to bucket cylinder (R.H.) Includes 1-30634 bushing and 1-DR10754 bushing | |
| D27680 | | LINK - bucket, dipper arm to bucket cylinder (L.H.) Includes 1-30634 bushing and 1-DR10754 bushing | |
| D27753 | CYLINDER ASSY. | CYLINDER - bucket, hydraulic (Without tie rods) See D25045 (See Figure 106 for breakdwon) When replacing cylinder with tie rods also order 1-218-5065 connector and 1-D29022 tube, dipper arm | |
| NSS | NOT SOLD SEPARAT | 3/4" JIC x 5/8" JIC straight connector (218-5065), dipper arm | |
| D28266 | WASHER | - special (1-17/64" I.D. x 2-1/8" O.D. x 7/64" thick) D23354 and D23358 pins, dipper arm | |
| D29512 | | ARM - dipper (Includes 2-D23203 bushings, 4-D25029 bushings, and 4-D23203 bushings, 4-D25029 bushings, and 4-D23444 bushings) When stock is exhausted use D31704, arm | |
| NSS | NOT SOLD SEPARAT | 1/8" NPT straight grease fitting (219-1), dipper arm | |
| D29983 | BUSHING | - D29992 dump link (See DR10011), dipper arm | |
| D29992 | | LINK - bucket dump (See D24909), dipper arm | |
| D30042 | WASHER | - special, D29992 link at bucket cylinder (1-9/16" I.D. x 3" O.D. x 3/16" thick), dipper arm | |
| D31704 | | ARM - dipper (Includes 2-D23203 bushings, 4-D25029 bushings, and 4-D31708 bushings) See D29512, ar | |
| NSS | NOT SOLD SEPARAT | 1/8" NPT straight grease fitting (219-1), dipper arm | |
| D31708 | BUSHING | - D31704 dipper arm at bucket pivot and bucket linkage (See D23444) | |
| DR10011 | BUSHING | - D24909 dump link (See D29983), dipper arm | |
| DR10754 | BUSHING | - D27679 and D27680 links at bucket cylinder pivot, dipper arm | |
